How To Hack Wifi-How To Hack Wifi Password In Android-How To Hack WIfi Password

Unknown 01:37
Hi In This Tutorial I am Going to show you the most searched query method on the internet_How to hack wifi password using the android device.Wifi Hacking is possible but its a little bit confusing.
Android System is based on Kali Linux system so you can perform any hacking trick on Android.But Android is not so Powerful as regular PC, in order to Some conditions and requirements to hack WIFI password.Many apps are available that claims to hack wifi password but all of them are useless.

How To Hack Wifi Password Using Android Device.


To Hack into wifi, you need following things:
For Better results use Cyanogen ROM.
Android Device should be rooted.
Android Device should support bcmon App (i.e., should have Broadcom bcm4329/4330 wifi chipset. [OR]
[Update] Now ‘non bcmon supported devices’ & ‘devices which support external WiFi cards’ can also be used to hack WiFi.
You Need Following tools too:
bcmon app[apk]:This Tool is used to enable Monitor Mode on Yourandroid device with Broadcom chipset, Download This App Here
Reaver for Android or RfA – It is a powerful pentest tool that can be used to crack was key after the WPS pin is cracked.it can retrieve the actual WPA-key. Download

Hacking WPA/WPA2 (WPS Enabled) WiFi using Android [bcmon supported devices]
First of all, Download the bcmon app and install it.
Now run the bcmon app.If it crashes for 3 to 4 times then your device is not supported.
Now install the firmware and tools.Now click on enable monitor mode.
Now Download Reaver and install it.
Run Reaver.



Reaver now scans for the available access points.Reaver can hack only WPS enabled WIFI.Make sure Monitor mode is turned on.Make sure that the “Automatic advanced settings” box are checked.



Now select the network that you want to hack and press Start Attack. It will launch the attack it can take about 2 to 10 hours to hack wifi.



Hacking WEP type WiFi Using Android Phone
WEP is an outdated encryption and has weak protocol.Now it is no more familiar.However, it is still used across the world due to lack of awareness.Follow the below instructions to hack WEP.
How To Hack WEP.
Run the bcmon terminal.The terminal is similiar to the most linux terminals.
Type in airodump-ng and tap the enter button.Now in newly opened window type in airodump-ng wlan0 and tap enter.



Now open reaver and note the wifi Name, wannaMac Address and broadcasting channel of wifi that you wants to hack into.Make sure it is using web encryption.Now we can start the scanning and collect packets. Type the following command.

airodump-ng -c channel# –bssid MAC address -w outputfile ath0

Note: channel# = broadcasting channel, MAC address = Mac Address of the router which you already noted down. -w is for specifying the output file name. I have given  outputfile in the example. So the complete command look similar to this.

airodump-ng -c 9 –bssid 00:14:6C:7E:40:80 -w outputfile ath0



Keep scanning until it collects about 20,000 to 30,000 packets.
Once enough packets are collected now go back to the terminal and type aircrack-ng outputfile*.cap and hit enter.Aircrack will attempt to crack wifi password from the collected packets.



It may take some hours to crack.When it will be cracked a message with Key Found  will be appeared,followed by the key in hexadecimal form.



Remove “:” from the key. i.e if it is 19:04:56:77:94, the key would be 190456779
Credits: XDA
Source :HackCave

Related Searches:
How to hack wifi

how to hack wifl password

how to hack wifi password on pc
how to hack wifl password android
how to hack wifl password in urdu
how to hack wifi password in androidI

how to hack wifi password in android mobile without software
how to hack wifi password in android mobile

how to hack wifi password in android phone

how to hack wifi password in android without any software

Artikel Terkait

Latest
Previous Article
Next Post »
Penulisan markup di komentar
  • Untuk menulis huruf bold gunakan <strong></strong> atau <b></b>.
  • Untuk menulis huruf italic gunakan <em></em> atau <i></i>.
  • Untuk menulis huruf underline gunakan <u></u>.
  • Untuk menulis huruf strikethrought gunakan <strike></strike>.
  • Untuk menulis kode HTML gunakan <code></code> atau <pre></pre> atau <pre><code></code></pre>, dan silakan parse kode pada kotak parser di bawah ini.

Disqus
Tambahkan komentar Anda

No comments